匹配方法
Matching method
方法1:啟動車輛使發動機與變速器達到正常工作溫度，掛前進檔行駛20米，慢踩剎車，直至車速為0保持檔位10S，同時觀看10組數據流，然后掛R檔行駛20米，慢踩剎車，直至車速為0保持檔位，同時觀看11組數據流，兩項OK了，完成自適應學習!
Method 1: start the vehicle to make the engine and transmission reach the normal operating temperature, shift to the forward gear for 20 meters, step on the brake slowly until the vehicle speed is 0 and keep the gear for 10s, and watch 10 groups of data streams at the same time, then shift to the R gear for 20 meters, step on the brake slowly until the vehicle speed is 0 and keep the gear, and watch 11 groups of data streams at the same time. The two items are OK, and the adaptive learning is completed!
方法2:啟動車輛使發動機與變速器達到正常工作溫度。掛前進檔使車速達到70km/h以上(手動模式要升至6檔)，然后點剎10次或在檔停車10秒以上;再掛倒檔行駛20米以上，然后在檔停車10秒以上即完成自適應學習。
Method 2: start the vehicle to make the engine and transmission reach normal operating temperature. Engage the forward gear to make the vehicle speed reach more than 70km/h (the manual mode should be raised to gear 6), and then brake for 10 times or stop in gear for more than 10 seconds; The self-adaptive learning is completed by driving in reverse gear for more than 20 meters, and then stopping in reverse gear for more than 10 seconds.
方法3：啟動車輛使發動機與變速器達到正常工作溫度。掛前進檔不踩油門，ECU會提高發動機轉速使之車速提高，向前行駛20，慢踩剎車，使之車速為0，要保持檔位，等待10S，然后掛R檔，行駛20米，方法同前進檔!
Method 3: start the vehicle to make the engine and transmission reach normal operating temperature. When engaging the forward gear without pressing the accelerator, the ECU will increase the engine speed to increase the vehicle speed. Drive forward for 20 minutes, slowly press the brake to make the vehicle speed 0. Keep the gear, wait for 10s, then engage the R gear and drive for 20 meters. The method is the same as that of the forward gear!
自適應方法
Adaptive method
1.以低功率驅動發動機，直到ATF油溫達到60-90°C。
1. drive the engine with low power until the ATF oil temperature reaches 60-90 ° C.
2、車輛停車時，發動機怠速，踩下制動踏板，從n變?yōu)镈，并保持此狀態約3秒。重復此過程五次。然后用同樣的方法從n變?yōu)镽。
2. When the vehicle is stopped, the engine is idling, press the brake pedal, change from n to D, and maintain this state for about 3 seconds. Repeat this process five times. Then change from n to R in the same way.
3、當車輛靜止時，換到D檔，小負載（油門踏板位置15-25%，測量數據塊02/2）將車輛加速到4檔（約80km/h）。然后讓汽車滑行到大約40公里/小時（不要踩剎車踏板），然后用適度的力量踩下剎車踏板，讓汽車停下來。車輛停止后，必須將車輛保持在“d”狀態約10秒鐘（踩下制動踏板）。重復整個步驟III六次。(6次0km/h->80->40->0)
3. When the vehicle is stationary, shift to gear d, and accelerate the vehicle to gear 4 (about 80km/h) with a small load (accelerator pedal position 15-25%, measurement data block 02/2). Then let the car slide to about 40 km / h (do not step on the brake pedal), and then press the brake pedal with moderate force to stop the car. After the vehicle is stopped, the vehicle must be kept in the "d" state for about 10 seconds (press the brake pedal). Repeat the entire step III six times. (6 times 0km/h->80->40->0)
4、將車輛加速至約70km/h并手動將其換至5檔（尖端）。然后以80-100nm發動機功率（見測量數據塊09）的恒定速度行駛約3-4分鐘。
4. Accelerate the vehicle to about 70km/h and manually shift it to 5th gear (tip). Then drive at a constant speed of 80-100nm engine power (see measurement data block 09) for about 3-4 minutes.
5、將車輛加速至約90km/h并手動將其換至6檔（尖端）。然后以80-100nm發動機功率（見測量數據塊09）的恒定速度行駛約2-3分鐘。
5. Accelerate the vehicle to about 90km/h and manually shift it to 6th gear (tip). Then drive at a constant speed of 80-100nm engine power (see measurement data block 09) for about 2-3 minutes.
6、
濟南自動變速箱維修提醒各位，當車輛靜止時，小負載將車輛加速至100km/h左右（油門踏板位置15-25%，測量數據塊02/2）。然后讓汽車滑行到40km/h左右（不要踩剎車踏板），再用一點力踩剎車踏板讓車停下。重復整個步驟六到五次。
6. Jinan automatic transmission maintenance reminds you that when the vehicle is stationary, a small load will accelerate the vehicle to about 100km/h (accelerator pedal position 15-25%, measurement data block 02/2). Then let the car slide to about 40km/h (do not step on the brake pedal), and then step on the brake pedal with a little force to stop the car. Repeat the entire procedure six to five times.
After explaining the matching and adaptive methods after transmission maintenance, you can follow our website www.jnbsx COM, learn more about the key points of consulting!
